Partner login
EN
The EVO3 Genesis One is a state of the art single cell sine wave generation system with extremely low THD. Think of the Genesis One as a dedicated mini power regeneration station for the connected electronics.
Unlike existing mains regenerators, IsoTek’s sine wave generation technology builds a completely new sine wave with extremely low distortion. A synchronous sine wave generator creates a fully optimized signal which is amplified by a generation engine running in either Class A/B or D (Genesis One), which is then fed to a high-quality output transformer with copper foil between the primary and secondary outputs, thus preventing distortion and noise passing through the unit. The result is up to 600W of continuous, newly generated power.
A critical part of the process is IsoTek’s unique synchronous sine wave system which replicates the frequency with zero variation so as not to create destructive harmonic distortions (beat frequencies) between the incoming mains supply and the generated electricity. In addition to eliminating distortion and producing an ultra-stable sine wave, the Genesis also controls mains voltage, ensuring the output voltage is maintained at 230V +/- 1%. By way of comparison, the European standard is 230V +/- 10%.
The end result is an extremely precise and consistent 230V/50Hz mains sine wave with vanishingly low levels of distortion, independent of the input quality of the power line. Whatever the level of distortion of the incoming mains supply, Genesis delivers exceptionally low THD (Total Harmonic Distortion) of between 0.05% and 0.17% with typical loads, remaining well below 0.3% with even the most complex loads.
Link to Sine Wave Generators: https://isoteksystems.com/categories/sine-wave-generators/
Every IsoTek product uses the finest grade electrical components, many custom made, using the highest quality metals and materials which are specifically designed for purpose. Quality doesn’t stop at parts but also extends into the PCB designs, which maintain high levels of amperage and extraordinarily low levels of resistance, using up to eight times the general standard of copper prior to pure silver plating.
Internal wiring also uses high purity coppers combined with silver plating, with either Fluorinated Ethylene Propylene (FEP) dielectric or IsoTek’s Virtual Dielectric of Air (VDA), where a FEP tube is wound around the conductor before an extruded FEP dielectric protects this construction giving unrivalled performance and the ultimate low resistance, high performance internal power delivery system.
Power surges or spikes on the mains supply are generally very bad for any electrical device especially a high quality audio replay system. Power surges occur when there is a boost to the electrical charge at some point in the power lines. This causes an increase in the electrical potential energy, which can increase the current flowing to your wall outlet. This in turn can damage your sensitive audio system.
The IsoTek protection system uses an array of VDRs which offer a cascading level of protection, in some cases over 100’000A. These step in fast and sequentially dependent upon the severity of the encountered power surge or spike. The architecture of the protection circuit extends dramatically and almost instantly when required.
The protection circuit has two primary functions, one to preserve itself and the second to step in gradually as any problem increases, with the ability to act very fast should an extreme condition occur. The protection circuits also protect the filters and the filters assist the protection in the initial stage. Unlike many protection devices these assist sound quality as well as providing protection. Studies suggest this problem is not subtle and is frequent. The disturbing challenge is the 1’000 to 6’000V range. It is likely most protection systems do very little good and probably cause sound degradation.
As one would expect the internal wiring of any IsoTek product is of the highest standard, ultra pure Ohno Continuous Cast copper solid core conductor strands with silver-plating offers low resistance and high amperage. A Fluorinated Ethylene Propylene (FEP) helix is wound around the conductor before an extruded FEP dielectric protects the conductor and creates a Virtual Dielectric of Air (VDA). This construction gives unrivalled performance and gives the ultimate low resistance, high performance internal power delivery system.
IsoTek’s internal wiring synergizes with the range of IsoTek power cables. One critical but overlooked area is maintaining commonality of design and material properties though an audio wiring loom, be it signal carrying cables or your power cable network.
Some IsoTek products (all V5) contain a System Link outlet, which is designed to connect multiple units together, maintaining a stared earth reference, and preserving the need for multiple wall outlet sockets.
This is particularly useful for joining multiple units together using our System Link cable available in EVO3 Initium, EVO3 Premier, EVO3 Sequel and EVO3 Optimum quality.
As part of our on-going commitment to the highest standards of customer service, IsoTek offers you the opportunity to extend the standard 2 years product warranty to 3 years, free of charge.
Simply register your purchase with IsoTek. We do not share your personal details with any third parties without your permission. To read our Privacy Policy please click here.
Unlike existing mains regenerators, IsoTek’s sine wave generation technology builds a completely new sine wave with extremely low distortion. A synchronous sine wave generator creates a fully optimized signal which is amplified by a generation engine running in either Class A/B or D (Genesis One), which is then fed to a high-quality output transformer with copper foil between the primary and secondary outputs, thus preventing distortion and noise passing through the unit. The result is up to 600W of continuous, newly generated power.
A critical part of the process is IsoTek’s unique synchronous sine wave system which replicates the frequency with zero variation so as not to create destructive harmonic distortions (beat frequencies) between the incoming mains supply and the generated electricity. In addition to eliminating distortion and producing an ultra-stable sine wave, the Genesis also controls mains voltage, ensuring the output voltage is maintained at 230V +/- 1%. By way of comparison, the European standard is 230V +/- 10%.
The end result is an extremely precise and consistent 230V/50Hz mains sine wave with vanishingly low levels of distortion, independent of the input quality of the power line. Whatever the level of distortion of the incoming mains supply, Genesis delivers exceptionally low THD (Total Harmonic Distortion) of between 0.05% and 0.17% with typical loads, remaining well below 0.3% with even the most complex loads.
Link to Sine Wave Generators: https://isoteksystems.com/categories/sine-wave-generators/
Every IsoTek product uses the finest grade electrical components, many custom made, using the highest quality metals and materials which are specifically designed for purpose. Quality doesn’t stop at parts but also extends into the PCB designs, which maintain high levels of amperage and extraordinarily low levels of resistance, using up to eight times the general standard of copper prior to pure silver plating.
Internal wiring also uses high purity coppers combined with silver plating, with either Fluorinated Ethylene Propylene (FEP) dielectric or IsoTek’s Virtual Dielectric of Air (VDA), where a FEP tube is wound around the conductor before an extruded FEP dielectric protects this construction giving unrivalled performance and the ultimate low resistance, high performance internal power delivery system.
Power surges or spikes on the mains supply are generally very bad for any electrical device especially a high quality audio replay system. Power surges occur when there is a boost to the electrical charge at some point in the power lines. This causes an increase in the electrical potential energy, which can increase the current flowing to your wall outlet. This in turn can damage your sensitive audio system.
The IsoTek protection system uses an array of VDRs which offer a cascading level of protection, in some cases over 100’000A. These step in fast and sequentially dependent upon the severity of the encountered power surge or spike. The architecture of the protection circuit extends dramatically and almost instantly when required.
The protection circuit has two primary functions, one to preserve itself and the second to step in gradually as any problem increases, with the ability to act very fast should an extreme condition occur. The protection circuits also protect the filters and the filters assist the protection in the initial stage. Unlike many protection devices these assist sound quality as well as providing protection. Studies suggest this problem is not subtle and is frequent. The disturbing challenge is the 1’000 to 6’000V range. It is likely most protection systems do very little good and probably cause sound degradation.
As one would expect the internal wiring of any IsoTek product is of the highest standard, ultra pure Ohno Continuous Cast copper solid core conductor strands with silver-plating offers low resistance and high amperage. A Fluorinated Ethylene Propylene (FEP) helix is wound around the conductor before an extruded FEP dielectric protects the conductor and creates a Virtual Dielectric of Air (VDA). This construction gives unrivalled performance and gives the ultimate low resistance, high performance internal power delivery system.
IsoTek’s internal wiring synergizes with the range of IsoTek power cables. One critical but overlooked area is maintaining commonality of design and material properties though an audio wiring loom, be it signal carrying cables or your power cable network.
Some IsoTek products (all V5) contain a System Link outlet, which is designed to connect multiple units together, maintaining a stared earth reference, and preserving the need for multiple wall outlet sockets.
This is particularly useful for joining multiple units together using our System Link cable available in EVO3 Initium, EVO3 Premier, EVO3 Sequel and EVO3 Optimum quality.
As part of our on-going commitment to the highest standards of customer service, IsoTek offers you the opportunity to extend the standard 2 years product warranty to 3 years, free of charge.
Simply register your purchase with IsoTek. We do not share your personal details with any third parties without your permission. To read our Privacy Policy please click here.
IsoTek’s EVO3 Genesis One is a highly compact state of the art full sine wave generation system, taking technology from IsoTek’s Ultimate Series Genesis.
This product is dedicated to powering front-end components up to a maximum of 100W from a single rear outlet. As most source components are under 50W in power consumption, it is possible to use this product in combination with IsoTek’s EVO3 Gemini power bar. Genesis One is compact measuring 75mm in width, 470mm deep and 125mm high housed in an extruded and machined aluminum chassis. At the rear is a single independent high current output socket designed to drive source components, CD players, DAC, pre-amplifiers and turntable motors. There is also an Auxiliary connection point for adding and powering additional IsoTek power cleaners. For example, a total of six Titan One, Nova One or Genesis One products can be positioned side by side to create a rack width unit.
The internal wiring is of the highest standard; ultra pure Ohno Continuous Cast copper solid core conductor strands with silver-plating offers low resistance and high amperage. A Fluorinated Ethylene Propylene (FEP) helix is wound around the conductor before an extruded FEP dielectric protects the conductor and creates a Virtual Dielectric of Air (VDA). This construction gives unrivalled performance and gives the ultimate low resistance, high performance internal power delivery system.
The internal wiring of IsoTek products synergizes with the range of IsoTek power cables. One critical but overlooked area is maintaining commonality of design and material properties though an audio wiring loom, be it signal carrying cables or your power cable network.
| NUMBER OF OUTLETS | 1 + System Link |
| OUTLETS (SINE WAVE GENERATION) | 100W |
| THD | 0.03% |
| VOLTAGE STABALISATION | 230V or 115V +/- 1% |
| MAINS INLET | 10A IEC C14 |
| MAINS VOLTAGE | 100 to 240V depending upon model |
| MAINS FREQUENCY | 50 to 60Hz depending upon model |
| SYSTEM LINK | x1 |
| DIMENSIONS (W x H x D) | 75 x 125 x 470mm |
| WEIGHT | 10Kg |
A high quality FEP provides a very low dielectric constant over a wide frequency range. The three conductors are given a slight rotational twist to aid RFI and EMI rejection, and are then surrounded by a cotton filler which give internal strength and reduce microphony.
The Titan One re-engineers IsoTek’s unique multi-award winning Direct-Coupled© technology into a discrete single cell version, offering the ultimate high current, low impedance power conditioner in the smallest form factor possible.
The EVO3 Gemini is a compact version of the award-winning EVO3 Polaris, featuring just two output sockets rated at 10A. Gemini is a cost-effective upgrade designed for simple two box audio or audio-visual systems or as a means to extend power outlets from the IsoTek EVO3 Genesis One Sine wave generators.
“IsoTek’s EVO3 Genesis One feeds components with up to 100 watts of power consumption with a flawless sine wave that frees the music playback from any power influence. Together with its siblings Titan One and Nova One, individual power preparations can be put together for complete systems.”
“The EVO3 Genesis One takes the sound of your system and removes its edginess and hardness. It doesn’t change the character of the presentation, just makes that presentation seem less ‘angular’ and harsh sounding. The overall presentation is just that bit more fluid, more able to process and draw together the themes within a piece of music.”
“Without any ifs or buts – with the EVO3 Genesis One, the IsoTek crew around mastermind Keith Martin have once again achieved a milestone in the power supply of a high-end system. Optimised for every application, IsoTek provides the perfect device. Especially for digital source devices there is probably nothing better for the money on the market than the EVO3 Genesis One – this is definitely true high-end. Hats off for this category!”
IsoTek’s Mosaic series offers a trio of compact power cleaning solutions in an elegant slim width format.
IsoTek has appointed distributors across the world to support its products and to give you the customer the best local service by professionals appointed through our distributors network. Please choose your country to find a local IsoTek supplier near you.
